P3788 Mitsubishi Auto Trouble Code
P3788 Mitsubishi Auto Trouble Code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission.
The crank but won't start condition, along with the trouble codes may make you think you've got a PATS anti-theft system problem. However, Ford reports that these codes are all related to software bugs. The only way around the problem is to reprogram the PCM with the latest software.
P3788 Mitsubishi Possible Solution:
Excessive air inflow can be caused by a vacuum leak, a dirty sensor or, an exhaust gas recirculation valve not closing properly. If the problem is not enough fuel, the culprit may be dirty injectors or fuel filters, a weak fuel pump or a leaky fuel pressure regulator. The lean fuel mix error may be accompanied by rough idling, engine misfires, hesitation during acceleration and overall poor engine performance.
P3788 Mitsubishi Description For All Models :
- Mitsubishi 3000
- Mitsubishi 360
- Mitsubishi 380
- Mitsubishi 500
- Mitsubishi A10
- Mitsubishi Airtrek
- Mitsubishi Aspire
- Mitsubishi Asx
- Mitsubishi Canter
- Mitsubishi Carisma
- Mitsubishi Celeste
- Mitsubishi Challenger
- Mitsubishi Chariot
- Mitsubishi Colt
- Mitsubishi Concept
- Mitsubishi Cordia
- Mitsubishi Cz
- Mitsubishi Dangan
- Mitsubishi Debonair
- Mitsubishi Delica
- Mitsubishi Diamante
- Mitsubishi Dingo
- Mitsubishi Dion
- Mitsubishi Eclipse
- Mitsubishi Eclipse Ii
- Mitsubishi Eclipse Iii
- Mitsubishi Ek-wagon
- Mitsubishi Endeavor
- Mitsubishi Field Guard
- Mitsubishi Fto
- Mitsubishi Galant
- Mitsubishi Galant Ix
- Mitsubishi Galant Viii
- Mitsubishi Gaus
- Mitsubishi Grandis
- Mitsubishi Gto
- Mitsubishi Hsr-v
- Mitsubishi I
- Mitsubishi Jeep
- Mitsubishi L200
- Mitsubishi L300
- Mitsubishi Lancer
- Mitsubishi Lancer Evo 10
- Mitsubishi Lancer Evo 8
- Mitsubishi Lancer Evo 9
- Mitsubishi Libero
- Mitsubishi Magna
- Mitsubishi Minica
- Mitsubishi Mirage
- Mitsubishi Model A
- Mitsubishi Montero
- Mitsubishi Mum
- Mitsubishi Nessie
- Mitsubishi Outlander
- Mitsubishi Outlander Ii
- Mitsubishi Outlander Iii
- Mitsubishi Pajero
- Mitsubishi Pajero Iii
- Mitsubishi Pajero Iv
- Mitsubishi Pistachio
- Mitsubishi Proudia
- Mitsubishi Raider
- Mitsubishi Rpm
- Mitsubishi Rvr
- Mitsubishi Sapporo
- Mitsubishi Se-ro
- Mitsubishi Shogun
- Mitsubishi Sigma
- Mitsubishi Space Star
- Mitsubishi Space Star Ii
- Mitsubishi Space Liner
- Mitsubishi Space Runner
- Mitsubishi Space Wagon
- Mitsubishi Spyder
- Mitsubishi Sss
- Mitsubishi Sst
- Mitsubishi Ssu
- Mitsubishi Starion
- Mitsubishi Sup
- Mitsubishi Suw
- Mitsubishi Tarmac
- Mitsubishi Toppo
- Mitsubishi Tredia
- Mitsubishi Valley
- Mitsubishi Verada
P3788 Mitsubishi Trouble Repair :
The sensors receive a 5 volt reference signal from the PCM. As pressure readings change, the sensor varies the voltage and the computer reads that to determine input. In the case of a broken wire, the sensor never sees the voltage and the computer assumes a major fault. So if you get this P3788 Mitsubishi code, first check to make sure you're getting a good 5 volt reference signal at the sensor.
|
Code Search
Please fill the search bar to find Auto Trouble Code meaning.